Plan the run, clip the lights, and switch them on the same day.
step 1
Measure the dimensions of the area where you plan to install the lights, mark the mounting positions for fixtures, and sketch a layout on paper.
Spending just 5 minutes on planning will save you from frantic scrambling later.
Draw a rough sketch first. It’s recommended to inspect the site at dusk before finalizing your layout.
step 2
Based on your measured dimensions, buy Color Bridge cables and LNT Track slightly longer than the measured length.
Next, select your preferred light fixtures (maximum 6 fixtures per set) and supporting accessories, then wait for your order to arrive.
A single Color Bridge cable has a maximum length of 15 meters. If additional length is needed, you may purchase outdoor waterproof socket posts locally.
step 3
Arrange the LNT Track following your sketch, then clip the Color Bridge cable into the LNT Track.
Insert the Color Bridge into the LNT Track.
For freestanding post installation, mount the LNT Track onto the supplied base. For wall or ceiling mounting, secure the track with screws.
step 4
Clip each light fixture onto the LNT Track, then twist with a screwdriver to lock it in place.
Every fixture features a locking slot: simply unlock it with a flathead screwdriver, slide it onto the LNT Track, then reset the lock to secure.
step 5
Once all fixtures are installed, plug the power adapter into a wall outlet. Power will run through the entire light circuit starting from one end of the track system.
Power adapters are available in 24W / 48W / 72W variants, matched to the quantity of fixtures you select.
step 6
You can switch the lights on/off, adjust brightness and RGBCW color modes via a remote control or mobile app.
If any fixture fails to illuminate, remove it and reattach it firmly to the LNT Track. Loose fitting is the most common cause.
If the fixture still does not light up after reinstallation, move it to a section of track confirmed to work to test the fixture itself.
step 1
Measure the dimensions of the area where you plan to install the lights, mark the mounting positions for fixtures, and sketch a layout on paper.
Spending just 5 minutes on planning will save you from frantic scrambling later.
Draw a rough sketch first. It’s recommended to inspect the site at dusk before finalizing your layout.
step 2
Based on your measured lengths, buy Color Bridge cables slightly longer than your measured distance.
Next, pick your preferred light fixtures (maximum 6 fixtures per set) and matching accessories, then wait for delivery.
The maximum length of a single Color Bridge cable is 15 meters. If extra length is needed, purchase outdoor waterproof socket posts locally.
step 3
Arrange the Color Bridge cables according to your sketch, which can be manually bent into various angles and curves.
Made of silicone, the cable holds its molded shape and can be freely styled
step 4
Clip each fixture onto the cable track, connect it to the Color Bridge via piercing terminals, and secure the fixtures to soil or gravel ground with ground stakes.
Every fixture comes with a twist cap: simply open the cap, clip the fixture onto the Color Bridge cable, then twist the cap closed
step 5
Once all fixtures are fitted, plug the power adapter into a wall socket. Power will feed the entire light string from one end of the cable.
Power adapters are available in 24W/48W/72W variants, matched to the number of fixtures you select
step 6
Control power on/off, brightness and RGBCW color modes via remote control or mobile app.
If any fixture fails to light up, remove it and reattach it firmly to the Color Bridge cable. This issue is almost always caused by loose fitting.
If re-installation still results in no light, move the fixture to a section of cable confirmed to work to test the fixture itself.
step 1
Measure the dimensions of the area where you plan to install the lights, mark the mounting positions for fixtures, and sketch a layout on paper.
Spending just 5 minutes on planning will save you from frantic scrambling later.
Draw a rough sketch first. It’s recommended to inspect the site at dusk before finalizing your layout.
step 2
Based on your measured lengths, buy Color Bridge cables slightly longer than your measured distance.
Next, pick your preferred light fixtures (maximum 6 fixtures per set) and matching accessories, then wait for delivery.
The maximum length of a single Color Bridge cable is 15 meters. If extra length is needed, purchase outdoor waterproof socket posts locally.
step 3
Arrange the Color Bridge cables following your sketch. Secure them by wrapping or using the GDJ screw-mount accessories.
The cable can be manually bent into all angles and curved shapes.
Made of silicone, the cable holds its molded shape and can be freely styled.
step 4
Clip each fixture onto the track, then pierce the Color Bridge cable to make electrical connections—only a screwdriver is required for installation.
Every fixture comes with a twist cap: simply open the cap, clip the fixture onto the Color Bridge cable, then twist the cap closed
step 5
Once all fixtures are fitted, plug the power adapter into a wall socket. Power will feed the entire light string from one end of the cable.
Power adapters are available in 24W/48W/72W variants, matched to the number of fixtures you select
step 6
Control power on/off, brightness and RGBCW color modes via remote control or mobile app.
If any fixture fails to light up, remove it and reattach it firmly to the Color Bridge cable. This issue is almost always caused by loose fitting.
If re-installation still results in no light, move the fixture to a section of cable confirmed to work to test the fixture itself.
DC24V cannot cause electric shock — handle it freely.
Sealed against rain and dust for year-round outdoor use.
Every connection is sealed — no bare conductor anywhere.
A loose clip or the wrong adapter causes most faults. Choose a question to see the fix.
Unclip it and re-seat the clip squarely onto the track so both contacts meet the conductors. If it still won’t light, move it to a spot you know works to tell the fixture apart from the position.
Color Bridge cuts to length between fixture positions — seal the cut end with a DC001 end cap. LNT rail is cut to size during sectioning. Always cut with the power disconnected.
Clip new fixtures onto any free length of track, up to your driver’s wattage. Tally the watts; if you’re near the 36W ceiling, step up to the 72W driver or add a second run.
A faint hum can be normal under load. Loud buzzing usually means the run exceeds the driver’s rating or the outlet is marginal — move to a 72W driver and a clean outlet.
Yes. Split a long layout into two runs, each fed by its own driver from its own end. Keep each run within its driver’s wattage rather than chaining drivers in series.
Use the sealed power-on connector and DC001 end caps — every junction is IP65 by design. Point cable entries downward so water sheds away, and leave slack so nothing pulls taut.
